660,
Taboot Street, P.O.Box No.49, PUNE-411001 [India] Ph: 6130791, Telefax: 6130017
Gram:
RAZON,E-mail: razonengg@usa.net,Website: www.razonengg.com
Polyurethane
Coating GHF-111 is general-purpose two component
polyurethane systems. Two components exactly pre-calculated and
pre-weighted quantities are supplied. The two components are mixed at site &
brush applied.
Polyurethane Coating GHF-111 is recommended
for floor
coating , external coatings, or coatings
of electronic
factory assembly
line flooring,
hospitals ,
Coating of
production plants in Pharmaceutical Industry, food, beverage -plants, terrace
water proofing treatment, aqueducts, basements, etc.
Surface
Preparation:
For Metal
surface:
Clean
metal surface thoroughly by sand blasting, to ensure the surface is free of
grease, rust
loose & flaky material. On dry dust
free surfaces apply primer coat &
coat Polyurethane
Coating GHF-111
as recommended
above. Alternatively scrub surface
thoroughly with wire brush
to remove dust, scales, rust etc. Our Metal Clean
may be
used to
remove all
grease, loose
rust flakes
etc. Clean surface thoroughly & coat Polyurethane Coating GHF-111.
For
Concrete Surface:
Wire brush
scrubbing to remove all
loose material, algae-fungus if any. Dust to remove
loose dust before coating with Polyurethane Coating GHF-111. If surface
is covered with oil, Wash surface
with mild acid followed by thorough washing & drying prior to treatment with
Polyurethane Coating GHF-111.
The surface
to be
treated should
be reasonably dry & free
of moisture. When applying Polyurethane Coating GHF-111
allow ample
ventilation and
avoid smoking.
Method
of use:
Stir
contents in
each of the containers. Mix
contents of the two pack container. Mix thoroughly. Use mixed contents
immediately.
Polyurethane coating GHF-111 are available in following
basic shades:
Clear, Red, Blue, Yellow, Green, White, Grey, Black.
[Other shades are also available on request.]
Packing: 1 ltr, 5 ltr, 25 ltr [combined hardner +
resin] packs.
|
NO |
PRODUCT – DATA
|
|
|
1 |
Colour |
Red, green, blue, yellow, white. |
|
2 |
Viscosity |
2000-3000 CPS after mixing |
|
3 |
Mixing ratio |
Mix entire contents of two pack system |
|
4 |
Method of Application |
Brush application |
|
5 |
Diluent |
Thinner – 3 |
|
6 |
Shelf Life |
1-2 years for unopened, unmixed content. |
|
7 |
Pot life |
2-3 hours at 30°–
40° C |
|
8 |
Texture |
Glossy – semi glossy |
|
9 |
Coverage capacity |
40-50 sq.ft./litre |
|
10 |
Film thickness |
40-50 mils |
|
11 |
Adhesion to metal concrete, any construction
materials. |
Excellent |
|
12 |
U.V. resistance |
Excellent |
|
13 |
Abrasion resistance |
Excellent |
|
14 |
Acid, Alkali resistance |
Resistant to acidic & alkaline Chemicals |
OTHER
PRODUCTS:
Coatings:
1) Rubberised Instant WaterProofer
2) White Water Proofer
3) Damp Proofer
4) Polyurethane Coating
5) Clear Water Proofer
6) Coal Tar Epoxy
Sealents:
1) Crack Seal
2) Rubberised Sealents
3) InstaSet -600
Admixtures:
1) Super Plasticizers 2) Accelerators 3) Retardex 4) Integral Water Proofer
5) Intrair [A.E.A] 6) Master Plaster 7) Rapid Grout 8) Anchorex 9) Hycrete RJ- 608 10) Block Master
11) Toughcrete
12) Brick Master
13) Tile Master 14)
Pipe Master
15) SLP
16)
PL-256
Other
Products:
1) Strextra NSG -110
2) P.A.Bound
3) P.A.Mortar
4) Repellant
5) Shutter Coat
6) Floor Repairs Mortars 7)
RZ-ED Mortar 8) Special
Grouting system
9) Concrete Cure Coating 10)
Tile Joint Sealer
11) Tile Fix #1
12) Instant Plugging Mortars 13) Easy Grout
14) Pipe Joint Sealer
Attention: It is strongly recommended that site
trials be conducted using site conditions and available raw materials to
evaluate the product. Since site materials and conditions are beyond our control
and since above suggestions and recommendations are based on our site
rials, laboratory product evaluation & trials, and since methods of
use at site is beyond our control. Hence, no guarantee can either be im plied or
enforceable