Cementitious
mortar, concrete needs
to be cured for 15 - 21 days
to remove heat of hydration for hydration and
to make up moisture loss due to evaporation
so that hydration reaction can proceed without interruption and full strength
could be developed.
Due to
scarcity of water or due to logistics on
large sites it may not be possible to cure with water (hence our Concrete Cure
Coating may be used).
In
arid climatic regions if the rate
of evaporation is very
high or for high stored buildings it may not be possible to cure external
plaster or concrete.
Lay
concrete as
usual , or
apply plaster
mortar as usual
allow ½
hour to 1 hour for setting
to commence. Take Concrete
Cure Coating
and water in ratio 1:1 upto
1:3 mix thoroughly apply on the freshly
surfaced mortar
by brush or spray. Ensure
entire surface is totally covered. Concrete Cure
Coating forms a
membrane and
enables retention of
moisture in
the mortar for efficient, effective
and complete hydration. Approximately 80 - 150 sq.ft. coverage is available with one kgs of
Concrete Cure Coating on reasonably smooth surface.
Concrete
Cure Coating
is used extensively for
curing plaster in high rise buildings, canals, slabs, and sloping roofs, curing
of mundaris, curing of scaffolding-holes-patch etc.
It is
imperative that
few trials are taken on site before implementing use of Concrete Cure
Coating, to obtain guaranteed and best results.
Concrete
Cure Coating is viscous white colored, water thinnable.
Available
in 25kg & 50kg packing.
NO
|
PRODUCT DATA |
|
|
1 |
Consistency |
White,
viscous emulsion |
|
2 |
Specific
gravity |
2.15 |
|
3 |
PH |
7.00 |
|
4 |
Toxicity
|
Nil |
|
5 |
Test
report |
Available
BS: 7542-1992 |
|
6 |
Percentage
solids |
60 - 65% |
|
7 |
Diluent |
Clean
water |
|
8 |
Life |
1-2 years
if stored in cool dry place away from sunlight. |
|
9 |
Packing |
25kgs,
50kgs carboys |
OTHER PRODUCTS:
Coatings:
1)
Rubberised Instant Water Proofer
2) White Water Proofer 3) Damp Proofer
4)
Polyurethane Coating
5) Clear Water Proofer
6) Coal Tar Epoxy
Sealents:
1) Crack
Seal
2) Rubberised Sealents
3) Insta Set -600
Admixtures:
1) Super
Plasticizers 2)
Accelerators 3)
Retardex
4) Integral Water Proofer
5) Intriar [A.E.A.]
6) Master Plaster 7) Rapid
Grout 8)
Anchorex
9)
Hycrete RJ- 608 10) Block
Maker 11)
Toughcrete 12)
Brick Master
13) Tile
Master
14) Pipe Master
15) SLP
16) PL-256
17) Block
Master
Other Products:
1)
Strextra NSG -110
2) P.A.Bound
3) P.A.Mortar
4) Shutter Coat
5)
Floor Repairs Mortars 6)
RZ-ED Mortar 7) Special
Grouting system 8) Tile Fix
#1
9) Tile
Joint Sealer
10) Instant Plugging Mortars 12)
Easy Grout 13)
Pipe Joint Sealer
Attention:
: It is strongly recommended that site trials be conducted using site conditions
and available raw materials to evaluate the product. Since site materials and
conditions are beyond our control and since above suggestions are
recommendations are based on our site trials and laboratory products evaluation
& trials, and since methods of use at site are beyond our control. Hence, no
guarantee is either implied or enforceable.